Reinke Manufacturing Company, Inc.: Safety Recalls in 2006

Updated on March 31, 2026.

There were 3 safety recalls made by Reinke Manufacturing Company, Inc. in 2006. See the details of the recalls below.

You can also see similar information for other manufacturers.

Data Source: NHTSA.

See this for other years:

June 9, 2006

(Campaign #: NR (Not Reported))

FRAME FLANGE FAILURE

ON CERTAIN CHASSIS FRAMES, THE LOWER FLANGE(S) OF THE FRAME CAN DEVELOP A CRACK EITHER IN FRONT OF OR BEHIND THE FRONT SUSPENSION HANGER.

NHTSA ID: 06V203000

Component: STRUCTURE

# of Units Affected: 32

Consequence Summary:

THE LOWER FLANGE(S) CAN FAIL, INCREASING THE RISK OF A CRASH.

Corrective Action:

REINKE WILL INSPECT AND REPAIR THE FRAME FLANGE(S) FREE OF CHARGE. THIS RECALL HAS BEEN SUPERSEDED BY CAMPAIGN 08V604.

Park Outside Advisory: No

Do not Drive Advisory: No

View Full Recall Details

May 30, 2006

(Campaign #: NR (Not Reported))

ALUMINUM TOOLBOX BRACKET

ON CERTAIN COMBINATION STEEL/ALUMINUM FLATBED, DROPDECK, AND ALUMINUM FLATBED TRAILERS EQUIPPED WITH MOUNTED TOOLBOXES, EACH TOOLBOX IS ATTACHED TO THE TRAILER WITH A MOUNTING SYSTEM THAT INCLUDES TWO ALUMINUM BRACKETS WHICH MAY HAVE DEVELOPED FATIGUE CRACKS ALONG THE BEND RADIUS LINES. SMALL CRACKS MAY FURTHER DEVELOP BASED ON TRAILER USAGE. THE BRACKET MAY BREAK CAUSING THE TOOLBOX TO SEPARATE FROM THE TRAILER.

NHTSA ID: 06V186000

Component:

# of Units Affected: 6

Consequence Summary:

IF THE TOOLBOX SEPARATES FROM THE TRAILER WHILE THE TRAILER IS IN MOTION, VEHICLES ON THE ROAD ARE AT RISK OF COLLISION WITH THE TOOLBOX AND ITS CONTENTS.

Corrective Action:

REINKE WILL LOCATE A CERTIFIED WELDER FOR OWNERS OF THE AFFECTED TRAILERS TO HAVE THE REMEDY PERFORMED. REINKE IS PROVIDING THE ALUMINUM GUSSETS ALONG WITH DETAILED INSTRUCTIONS FOR THE WELDER. THE RECALL BEGAN ON JUNE 22, 2006. OWNERS MAY CONTACT REINKE AT 1-877-762-1001.

Park Outside Advisory: No

Do not Drive Advisory: No

View Full Recall Details

May 23, 2006

(Campaign #: NR (Not Reported))

ALUMINUM TOOLBOX BRACKET BREAKS

CERTAIN REINKE ALUMINUM TOOLBOX BRACKETS, P/NO. 223021, SOLD AS AFTERMARKET EQUIPMENT FOR USE ON REINKE TRAILERS. DURING MANUFACTURE, THE BEND RADIUS OF THE BRACKETS WAS TOO SMALL RESULTING IN BRACKETS WITH GREATLY REDUCED FATIGUE LIFE. SMALL CRACKS MAY DEVELOP ALONG THE BEND RADIUS LINES OF THE BRACKETS IF INSTALLED AS PART OF THE TOOLBOX MOUNTING SYSTEM. THE CRACKS MAY FURTHER DEVELOP AND THE BRACKETS MAY BREAK CAUSING THE TOOLBOX TO SEPARATE FROM THE TRAILER.

NHTSA ID: 06E048000

Component:

# of Units Affected: 20

Consequence Summary:

IF THE TOOLBOX SEPARATES FROM THE TRAILER WHILE THE TRAILER IS IN MOTION, VEHICLES ON THE ROAD ARE AT RISK OF COLLISION WITH THE TOOLBOX AND ITS CONTENTS AND A VEHICLE CRASH COULD OCCUR WITHOUT WARNING.

Corrective Action:

REINKE WILL NOTIFY ITS CUSTOMERS AND REINFORCE THE BRACKETS WITH ALUMINUM GUSSETS THAT WILL BE WELDED ON EACH SIDE OF EACH BRACKET FREE OF CHARGE. THE RECALL BEGAN ON JUNE 22, 2006. OWNERS WHO DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT REINKE TOLL-FREE AT 877-762-1001.

Park Outside Advisory: No

Do not Drive Advisory: No

View Full Recall Details