Nissan North America, Inc.: Safety Recalls in 2011

NISSAN IS RECALLING CERTAIN MODEL YEAR 2011 INFINITI FX, MODEL YEAR 2012 INFINITI M, MODEL YEAR 2011-2012 NISSAN FRONTIER, MODEL YEAR 2011-2012 NISSAN XTERRA, MODEL YEAR 2011-2012 NISSAN PATHFINDER, AND MODEL YEAR 2012 NISSAN NV VEHICLES. SOME OF THE BOLTS THAT CONNECT THE ENGINE OIL COOLER AND THE ENGINE OIL FILTER TO THE ENGINE IN THESE VEHICLES MAY HAVE BEEN MANUFACTURED TO BELOW SPECIFICATION STRENGTH. AS A RESULT, THE BOLT MAY BREAK AT THE OIL FILTER ATTACHMENT POINT AND CAN CAUSE AN ENGINE OIL LEAK.

NISSAN IS RECALLING CERTAIN MODEL YEAR 2010-2011 SENTRA VEHICLES EQUIPPED WITH MR20 ENGINES, MANUFACTURED FROM MAY 11, 2010, TO MAY 22, 2010, AND JULY 8, 2010, TO OCTOBER 25, 2010. THE ZINC COATING APPLIED TO THE TERMINAL STUD BOLT WAS THICKER THAN SPECIFICATION. THIS CAN RESULT IN A VOLTAGE DROP THAT MAY CAUSE DIFFICULTY STARTING THE VEHICLE AND COULD CAUSE DAMAGE TO THE ENGINE CONTROL MODULE (ECM).

NISSAN IS RECALLING CERTAIN MODEL YEAR 2011 NISSAN JUKE VEHICLES MANUFACTURED FROM APRIL 9, 2010, THROUGH MAY 12, 2011. THE TURBOCHARGER BOOST SENSOR BRACKET MAY SEPARATE FROM THE AIR INLET TUBE DUE TO A DEFECTIVE WELD.

NISSAN IS RECALLING CERTAIN MODEL YEAR 2011 ROGUE VEHICLES MANUFACTURED FROM AUGUST 17, 2010, THROUGH OCTOBER 30, 2010. THE CIRCUIT BOARD MAY NOT HAVE BEEN INSTALLED IN THE CORRECT POSITION ON CERTAIN ELECTRIC POWER STEERING (EPS) ASSIST CONTROL UNITS. THIS MAY CAUSE ADDITIONAL STRESS ON THE SOLDER OF THE TERMINAL TO THE CIRCUIT BOARD RESULTING IN THE SOLDER CRACKING AND SEPARATING COMPLETELY FROM THE CIRCUIT BOARD.

NISSAN IS RECALLING CERTAIN MODEL YEAR 2011 AND 2012 INFINITI G37 COUPE VEHICLES AND CERTAIN MODEL YEAR 2011 NISSAN 370Z VEHICLES MANUFACTURED FROM JULY 2, 2011, THROUGH AUGUST 29, 2011. DUE TO A PROGRAMMING ERROR, THE POWER WINDOW SWITCH CONTROLLER IN THE SUBJECT VEHICLES WAS MANUFACTURED OUT OF SPECIFICATION.

NISSAN IS RECALLING CERTAIN MODEL YEAR 2012 NISSAN ALTIMA VEHICLES MANUFACTURED FROM JUNE 15, 2011, THROUGH JUNE 21, 2011 AND MODEL YEAR 2012 NISSAN NV VEHICLES MANUFACTURED FROM JUNE 23, 2011, THROUGH JUNE 28, 2011 BECAUSE THE AIR BAG CONTROL UNIT (ACU) WAS ASSEMBLED INCORRECTLY.

NISSAN IS RECALLING CERTAIN MODEL YEAR 2011-2012 NISSAN ALTIMA SEDAN VEHICLES MANUFACTURED FROM APRIL 25, 2011, THROUGH JUNE 10, 2011 AT THE CANTON, MISSISSIPPI PLANT. THE TRANSVERSE LINK BOLT MAY NOT HAVE BEEN TORQUED TO THE PROPER SPECIFICATION. THIS CONDITION COULD CAUSE THE BOLT TO BECOME LOOSE WHILE THE VEHICLE IS BEING DRIVEN, CREATING A RATTLING NOISE AND VIBRATION.

NISSAN IS RECALLING CERTAIN MODEL YEAR 1996-2004 PATHFINDER AND MODEL YEAR 1997-2003 INFINITI QX4 VEHICLES ORIGINALLY SOLD, OR CURRENTLY REGISTERED IN, CONNECTICUT, DELAWARE, IOWA, ILLINOIS, INDIANA, MASSACHUSETTS, MAINE, MARYLAND, MICHIGAN, MINNESOTA, MISSOURI, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT, WASHINGTON D.C., WEST VIRGINIA AND WISCONSIN. IN AREAS OF THE COUNTRY IN WHICH HEAVY CONCENTRATIONS OF ROAD SALT ARE USED, A MIXTURE OF SNOW/WATER AND SALT MAY ENTER AN ASSEMBLY LOCATION HOLE IN THE UPPER STRUT HOUSING, CAUSING WATER TO COLLECT AT THE MATING SURFACE OF THE STRUT HOUSING PANEL AND THE INNER HOOD LEDGE ASSEMBLY. OVER TIME, THIS SNOW/WATER AND SALT INTRUSION MAY RESULT IN CORROSION OF THE STRUT TOWER HOUSING IN SOME SUBJECT VEHICLES.