Ford Motor Company: Safety Recalls in 2000

VEHICLE DESCRIPTION: LIGHT DUTY TRUCKS AND CAB CHASSIS EQUIPPED WITH GASOLINE ENGINES AND DUAL FUEL TANKS. THE CARBON STEEL FUEL PRESSURE REGULATOR IN THE FUEL SYSTEM CAN WEAR OUT DURING THE LIFE OF THE VEHICLE. IF THE FUEL PRESSURE REGULATOR MALFUNCTIONS, IT CAN CAUSE HIGH FUEL SYSTEM PRESSURE, WHICH DAMAGES THE FUEL PUMP CHECK VALVE. THIS ALLOWS FUEL TO BE TRANSFERRED FROM ONE TANK TO THE OTHER, POSSIBLY OVERFILLING THE NON-OPERATING TANK, RESULTING IN FUEL OVERFLOW PAST THE FILLER CAP.

VEHICLE DESCRIPTION: SPORT UTILITY VEHICLES EQUIPPED WITH 4.0L SOHC ENGINES AND STILL RETAIN THE ORIGINAL THROTTLE BODY (PART NUMBERS 97JF-9E926AB OR 97JF-9E926-AC). SOME OF THE ORIGINAL THROTTLE BODIES INSTALLED ALLOWED A GAP BETWEEN THE PLATE AND BORE TO BE BUILT TOO NARROW. THIS REDUCED CLEARANCE ALLOWED THE ENGINE DEPOSITS NORMALLY PRESENT IN THE THROTTLE BODY TO CONTACT OR BRIDGE THE GAP. IF THE ENGINE DEPOSITS BRIDGED THE GAP BETWEEN THE THROTTLE PLATE AND BORE AND THEN HARDENED, ON THE INITIAL APPLICATION OF THE ACCELERATOR PEDAL AFTER THE ENGINE HAS COOLED, THE OPERATOR WOULD NEED TO APPLY ADDITIONAL FORCE TO THE ACCELERATOR PEDAL TO BREAK THE BRIDGE.

VEHICLE DESCRIPTION: MINIVANS EQUIPPED WITH 3.0L ENGINES. AN ACCELERATOR CABLE WAS KINKED DURING INSTALLATION, CAUSING THE CORE WIRES TO EVENTUALLY FRAY.

VEHICLE DESCRIPTION: STATION WAGONS AND 3-DOOR VEHICLES. THE SUBJECT VEHICLES HAVE A FOLDING 60/40 SECOND SEAT THAT BECOMES A LOAD FLOOR IN THE FOLDED POSITION. WHEN THE 60% PORTION OF THE SEAT IS FOLDED DOWN AND A LOAD IS APPLIED TO THE FRONT EDGE OF THE LOAD FLOOR, THE OUTBOARD HINGE PIVOT COULD DISENGAGE FROM THE HINGE.

VEHICLE DESCRIPTION: CERTAIN LIMOUSINES STRETCHED OVER 60 INCHES FAIL TO COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 109, "NEW PNEUMATIC TIRES," AND NO. 110, "TIRE SELECTION AND RIMS."

VEHICLE DESCRIPTION: MINIVANS AND PASSENGER VEHICLES. A RESTRAINT CONTROL MODULE (RCM) OR A SIDE OR FRONT CRASH SENSOR MAY HAVE BEEN ASSEMBLED WITH ONE OR MORE OF THE SCREWS THAT MOUNT THE CIRCUIT BOARD IN THE HOUSING MISSING. IF SOME OR ALL OF THE SCREWS ARE MISSING, THE PERFORMANCE OF THE OCCUPANT RESTRAINS COULD BE AFFECTED.

VEHICLE DESCRIPTION: PASSENGER VEHICLES. A DECKLID WIRE HARNESS CAN FATIGUE AND DEVELOP BROKEN WIRES IN THE BEND AREA OF THE WIRE HARNESS.

VEHICLE DESCRIPTION: SPORT UTILITY VEHICLES. UNDER CERTAIN CONDITIONS, A FRONT SWAY BAR LINK CAN FRACTURE.

VEHICLE DESCRIPTION: SPORT UTILITY VEHICLES EQUIPPED WITH THE 3.27 OR 3.55 AXLE RATION. THE SUBJECT VEHICLES HAVE A POWERTRAIN CONTROL MODULE THAT COULD ALLOW THE VEHICLE TO EXCEED THE DESIGN INTENT TOP SPEED. AT THESE EXTREME SPEEDS, THE VEHICLE COULD BE CAPABLE OF EXCEEDING THE SPEED RATING OF THE TIRE.

VEHICLE DESCRIPTION: SPORT UTILITY VEHICLES WITH STEEL HOODS AND CERTAIN PICKUP TRUCKS EQUIPPED WITH SHEET MOLDING COMPOUND HOODS. A WIRE FORMED HOOD STRIKER COULD BE SUSCEPTIBLE TO FATIGUE FRACTURES. IF THE HOOD STRIKER FRACTURES, THE HOOD COULD FLY OPEN WHILE THE VEHICLE IS BEING DRIVEN.

VEHICLE DESCRIPTION: MOTOR HOME CHASSIS AND HEAVY DUTY TRUCKS. THE AFFECTED VEHICLES HAVE TIE ROD ENDS AND/OR DRAG LINK ASSEMBLY ENDS THAT COULD HAVE INSUFFICIENT HARNESS IN THE BALL STUD.

VEHICLE DESCRIPTION: CERTAIN SPORT UTILITY VEHICLES, PICKUP TRUCKS, AND PASSENGER VEHICLES FAIL TO COMPLY WITH THE REQUIREMENTS OF FMVSS 225, "CHILD RESTRAINT ANCHORAGE SYSTEMS." THE AFFECTED EXPEDITION/NAVIGATOR OWNER GUIDES DO NOT IDENTIFY THE LOCATIONS OF SEATING POSITIONS EQUIPPED WITH TETHER ANCHORAGES, AND DO NOT PROVIDE INSTRUCTIONS FOR SECURING CHILD SEATS TO THESE TETHER ANCHORAGES. THE F150 SC OWNER GUIDES DO NOT PROVIDE THE PROCEDURE FOR SECURING CHILD SEATS TO THE TETHER ANCHORAGES. THE TAURUS/SABLE OWNER GUIDES DO NOT IDENTIFY THE CENTER REAR SEATING POSITION AS HAVING LATCH COMPATIBLE LOWER ANCHORAGES.

VEHICLE DESCRIPTION: SPORT UTILITY VEHICLES. THE WINDSHIELD WIPER LINKAGE CAN DISENGAGE DUE TO A BROKEN BALL SOCKET.

VEHICLE DESCRIPTION: CERTAIN PASSENGER VEHICLES WITH MEDIUM GRAPHITE SEAT BELTS FAIL TO COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 209, "SEAT BELT ASSEMBLIES." AN INCORRECT FRONT CENTER SEAT BELT AND RETRACTOR ASSEMBLY MAY HAVE BEEN INSTALLED.

VEHICLE DESCRIPTION: PASSENGER VEHICLES WITH MIDNIGHT BLACK OR MEDIUM PARCHMENT SEAT BELTS MANUFACTURED ON JULY 31, 2000, FAIL TO COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 209, "SEAT BELT ASSEMBLIES." AN INCORRECT DRIVER'S SIDE REAR SEAT BELT AND RETRACTOR ASSEMBLY MAY HAVE BEEN INSTALLED.

VEHICLE DESCRIPTION: 1995 PASSENGER VEHICLES EQUIPPED WITH THE 2.0L AND 2.5L ENGINES, AND 1996 VEHICLES EQUIPPED WITH 2.5L ENGINES. TIGHTENING OF THE ENGINE COOLING FAN MOTOR BEARINGS, UP TO AND INCLUDING MOTOR STALL, CAN RESULT IN INCREASED MOTOR TORQUE AND HIGHER THAN NORMAL MOTOR CURRENT AND ACCOMPANYING HIGH MOTOR TEMPERATURES.

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE FRONT SUSPENSION LOWER BALL JOINTS WERE NOT TIGHTENED TO SPECIFICATIONS WHEN THEY WERE ATTACHED TO THE LOWER CONTROL ARMS.

VEHICLE DESCRIPTION: PASSENGER VEHICLES EQUIPPED WITH 4.6L ENGINES. A COOLANT FLOW BLOCKAGE EXISTS AT THE INTAKE MANIFOLD HEATER CORE NIPPLE RESULTING IN NO COOLANT FLOW TO THE HEATER AND, THEREFORE, NO WARM AIR FLOW FROM THE HEATER OR WINDSHIELD DEFROSTER. VEHICLES WITH THIS CONDITION DO NOT COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 103, "WINDSHIELD DEFROSTING AND DEFOGGING SYSTEMS."

VEHICLE DESCRIPTION: REGULAR CAB PICKUP TRUCKS. THE DRIVER SIDE SEAT BELT RETRACTOR MAY NOT FULLY RETRACT THE BELT.

VEHICLE DESCRIPTION: BI-FUEL VEHICLES. THESE VEHICLES MAY HAVE A FUEL TANK FILLER PIPE GROMMET THAT COULD HAVE BEEN DAMAGED DURING THE INSTALLATION OF THE BI-FUEL SYSTEM. IF THE GROMMET IS DAMAGED, FUEL COULD LEAK. FUEL LEAKAGE IN THE PRESENCE OF AN IGNITION SOURCE COULD RESULT IN A FIRE. DEALERS WILL REPLACE THE FUEL TANK FILLER PIPE GROMMET.

VEHICLE DESCRIPTION: MINIVANS BUILT WITH INSTRUMENT CLUSTERS WITHOUT THE MESSAGE CENTER, FAIL TO COMPLY WITH THE REQUIREMENTS OF STANDARD NO. 118, "POWER-OPERATED WINDOW, PARTITION, AND ROOF PANEL SYSTEMS." THE POWER WINDOWS MAY BE OPERABLE AFTER THE IGNITION HAS BEEN TURNED TO THE "OFF" POSITION AND THE FRONT DOORS ARE OPENED.

VEHICLE DESCRIPTION: PASSENGER VEHICLES EQUIPPED WITH MANUAL TRANSMISSIONS. IF A VEHICLE IS PARKED WITH THE PARKING BRAKE NOT FULLY APPLIED AND NOT IN FIRST GEAR, AS DIRECTED IN THE OWNER GUIDE, AND THE SELF ADJUSTMENT PAWL SUBSEQUENTLY SKIPS ONE OR TWO TEETH, THE VEHICLE COULD MOVE ON SOME GRADES.

VEHICLE DESCRIPTION: MINI VANS. THESE VEHICLES MAY HAVE THE PLASTIC TRIM COVER AROUND THE BASE OF THE FRONT SEAT SAFETY BELT BUCKLE TRAPPED BETWEEN THE SHOULDER OF THE RESTRAINT ANCHORAGE BOLT AND THE SEAT PEDESTAL. THIS COULD EVENTUALLY ALLOW THE SEAT BELT BUCKLE BOLT TO LOOSEN.

VEHICLE DESCRIPTION: MEDIUM DUTY TANDEM REAR AXLE TRUCKS WITH ABS. THESE VEHICLES FAIL TO COMPLY WITH FMVSS NO. 121, "AIR BRAKE SYSTEMS." THE AIR BRAKE SYSTEM WAS PLUMBED SO THAT COMPLETE AIR RESERVOIR ISOLATION WAS NOT PROVIDED. SOME VEHICLES WERE BUILT WITH AN AIR LINE FROM THE SYSTEM ECU RELAY VALVE MODULE TEE FITTING, INCORRECTLY CONNECTED TO THE SYSTEM SUPPLY TANK, RATHER THAN THE SYSTEM AUXILIARY PRIMARY TANK.

VEHICLE DESCRIPTION: CERTAIN SPORT UTILITY VEHICLES FAIL TO COMPLY WITH THE REQUIREMENTS OF PART 567.4, "CERTIFICATION." THESE VEHICLES WERE SHIPPED FROM THE ASSEMBLY PLANT WITHOUT SAFETY CERTIFICATION LABELS.

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE REAR WHEEL HUB RETAINING NUTS CAN LOOSEN AND ALLOW THE LEFT REAR WHEEL AND BRAKE DRUM ASSEMBLY TO SEPARATE FROM THE VEHICLE.

VEHICLE DESCRIPTION: PASSENGER VEHICLES EQUIPPED WITH SPEED CONTROL AND AUTOMATIC TRANSMISSION. A SPEED CONTROL CABLE COULD HAVE A CORE WIRE THAT IS LONG ENOUGH TO CATCH ON THE SLEEVE AT THE THROTTLE BODY END OF THE CABLE DURING WIDE-OPEN THROTTLE ACCELERATION.

VEHICLE DESCRIPTION: MINI VANS. ONE OR MORE OF THE FIVE BOLTS THAT MOUNT THE RACK AND PINION STEERING GEAR TO THE VEHICLE MAY HAVE BEEN INCORRECTLY TIGHTENED.

VEHICLE DESCRIPTION: CERTAIN CREW VANS FAILED TO COMPLY WITH THE REQUIREMENTS OF FMVSS 225, "CHILD RESTRAINT ANCHORAGE SYSTEMS." THESE VEHICLES, WHICH ARE DESIGNATED AS TRUCKS, ARE 5 PASSENGER VEHICLES WITH THREE DESIGNATED SEATING POSITIONS IN THE SECOND ROW SEATS. THEY WERE BUILT WITHOUT CHILD SEAT TETHER ANCHORAGE BRACKETS IN THE CENTER POSITION OF THE SECOND ROW SEAT. ALSO THE OWNER GUIDES DO NOT ADDRESS THE CHILD SEAT TETHER ANCHORAGES IN THE CENTER SECOND ROW SEAT POSITION.

VEHICLE DESCRIPTION: BI-FUEL CNG PICKUP TRUCKS AND BI-FUEL CNG VANS, MODIFIED BY CFI CONTROL SYSTEMS, INC., FAIL TO CONFORM TO THE REQUIREMENTS OF FMVSS NO. 303, "FUEL SYSTEM INTEGRITY OF COMPRESSED NATURAL GAS VEHICLES." THE LABEL AFFIXED TO THE FUEL FILLER DOOR BY THE VEHICLE MODIFIER CONTAINS THE INSPECTION DATE AND EXPIRATION DATE OF THE CNG TANK. HOWEVER, IT DOES NOT CONTAIN THE STATEMENT "SEE INSTRUCTIONS ON THE FUEL CONTAINER FOR INSPECTION AND SERVICE LIFE."

VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS BUILT WITH BENDIX AIR ABS WITH AN EC-17 1030R ELECTRONIC CONTROL UNIT (ECU), THERE HAVE BEEN REPORTS OF UNWANTED ABS ACTIVATION AT LOW SPEEDS CAUSED BY 1) CHAFED ABS WHEEL SPEED SENSOR WIRES ON ROTATING PARTS OR 2) A DAMAGED COMPONENT AT THE WHEEL END THAT GENERATES A CERTAIN TYPE OF ERRATIC SENSOR SIGNAL.

VEHICLE DESCRIPTION: SPORT UTILITY VEHICLES. THE O-RING SEALS IN THE FUEL LINE CONNECTOR AT THE OUTLET END OF THE FUEL FILTER WERE DAMAGED WHEN THE LINE WAS CONNECTED TO THE FILTER DURING VEHICLE ASSEMBLY. IN SOME CASES, THIS DAMAGE COULD RESULT IN A FUEL ODOR, OR POSSIBLY IN FUEL DRIPPING FROM THE CONNECTION.

CERTAIN PASSENGER VEHICLES, LIMOUSINES, AND MINI VANS WERE BUILT WITH A NEWLY DESIGNED RESTRAINT CONTROL MODULE (RCM). IN SOME CASES, THE RCM DOES NOT RECOGNIZE CERTAIN SYSTEM FAULTS THAT COULD RESULT IN AN AIR BAG OR SEAT BELT PRE-TENSIONER UNEXPECTEDLY ACTIVATING DURING THE SELF-TEST SEQUENCE AT VEHICLE START-UP.

VEHICLE DESCRIPTION: SOME 4X2 SPORT UTILITY VEHICLES NOT EQUIPPED WITH AN ANTILOCK BRAKING SYSTEM MAY HAVE INADVERTENTLY BEEN BUILT WITH 4X4 REAR HUBS INSTEAD OF 4X2 HUBS. IF THE INCORRECT HUBS ARE INSTALLED ON A 4X2 VEHICLE, THE REAR WHEELS CAN LOOSEN, OR IN SOME CASES, SEPARATE FROM THE VEHICLE.

VEHICLE DESCRIPTION: MOTOR HOME CHASSIS. THESE VEHICLES MAY HAVE A MIS-ROUTED WIRE HARNESS THAT ATTACHES TO THE BRAKE PEDAL POSITION SWITCH. THE WIRE COULD RUB ON THE STEERING COLUMN, RESULTING IN A SHORT CIRCUIT AND A BLOWN FUSE, CAUSING A LOSS OF STOP LAMP FUNCTION.

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE CHILD SAFETY SEAT ANCHOR LATCH (ISO-FIX ANCHOR) FASTENERS DO NOT HAVE ADEQUATE RESIDUAL TORQUE. THE ANCHORS ARE SECURED TO THE FLOOR PAN WITH A REINFORCEMENT PLATE THAT HAS TWO STUDS THAT EXTEND UPWARD THROUGH THE FLOOR PAN AND THE ISO-FIX ANCHOR. THE SEALER ON THE FLOOR PAN COULD CAUSE A SOFT JOINT AND, EVEN IF THE NUTS ARE PROPERLY TORQUED, ROAD VIBRATIONS COULD CAUSE THE NUT TO WORK ITS WAY COMPLETELY OFF THE STUD.

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE "VEHICLE CAPACITY WEIGHT" AND "DESIGNATED SEATING CAPACITY" INFORMATION WAS NOT PRINTED ON THE SAFETY CERTIFICATION LABELS AFFIXED TO THESE VEHICLES. ON AFFECTED SABLE SEDAN VEHICLES, THE "VEHICLES CAPACITY WEIGHT" (AND ALSO THE LUGGAGE LOAD) INFORMATION PRINTED ON THIS LABEL IS INCORRECT - SABLE WAGON LUGGAGE LOAD WAS INCORRECTLY USED FOR THE SABLE SEDAN. THESE VEHICLES DO NOT COMPLY WITH THE LABEL REQUIREMENTS OF FMVSS NO. 110, "TIRE SELECTION AND RIMS."

TRUCKS EQUIPPED WITH ALLISON 1000 OR 2400 SERIES TRANSMISSIONS. THESE TRANSMISSIONS CAN EXPERIENCE PARK PAWL TO REAR COVER INTERFERENCE DUE TO AN OUT OF FLATNESS CONDITION.

VEHICLE DESCRIPTION: PASSENGER VEHICLES, LIGHT DUTY TRUCKS, SPORT UTILITY VEHICLES, AND MINI VANS EQUIPPED WITH TRW SEAT BELT BUCKLE ASSEMBLIES. THE BUCKLE BASE OF THESE SEAT BELT ASSEMBLIES WERE NOT PROPERLY HEAT TREATED AND THEREFORE DO NOT PASS THE LOAD BEARING REQUIREMENT OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 209, "SEAT BELT ASSEMBLIES."

VEHICLE DESCRIPTION: LIGHT DUTY PICKUP TRUCKS MANUFACTURED AT THE KANSAS CITY OR NORFOLK ASSEMBLY PLANTS. THE FRONT FUEL LINE ASSEMBLY COULD HAVE A HOLE RUBBED THROUGH IN ONE OF TWO LOCATIONS. THE FIRST LOCATION IS BELOW THE FUEL RAIL CONNECTION WHERE THE FLEXIBLE HOSE IS CRIMPED TO THE STEEL TUBE. THE BRACKET THAT ATTACHES THE FRONT FUEL LINE TO THE TRANSMISSION COULD HAVE BEEN BENT DURING ASSEMBLY. THE SECOND LOCATION IS AT THE REAR STEEL TUBE SECTION FORWARD OF THE REAR BRACKET. DURING INSTALLATION THE REAR STEEL TUBES OF THE FRONT FUEL LINE ASSEMBLY COULD HAVE BEEN BENT DOWNWARD. IN VEHICLES EQUIPPED WITH A MANUAL 4XZ4 TRANSFER CASE SHIFTER, THE SHIFTER LINKAGE MAY CONTACT THE STEEL TUBES AS IT IS BEING SHIFTED BETWEEN 4H, 4L, 2L AND NEUTRAL.

VEHICLE DESCRIPTION: PASSENGER VEHICLES. CERTAIN VEHICLES FAIL TO COMPLY WITH REQUIREMENTS OF FMVSS NO. 201, "OCCUPANT PROTECTION IN INTERIOR IMPACT." THE RESULTANT HIC(D) VALUE AT ONE TARGET LOCATION AP1, LOCATED ON THE TRIM PANEL AT THE JUNCTURE OF THE A-PILLAR AND ROOF SIDE RAIL, MAY BE GREATER THAN DESIGN INTENT.

VEHICLE DESCRIPTION: SPORT UTILITY VEHICLES EQUIPPED WITH SPEED CONTROL. THE SPEED CONTROL CABLE CAN HAVE A CRACKED OR MISSING SPEED CONTROL CABLE SERVO CAP LOCATING TAB. THE LOCATING TAB COULD ENTER THE SERVO CLUTCH CAVITY AND INTERFERE WITH THE SPEED CONTROL SERVO CLUTCH. ALSO, WATER COULD ENTER THOSE UNITS THAT CONTAIN A CRACKED OR MISSING SERVO CAP LOCATING TAB, EVENTUALLY CAUSING CORROSION THAT COULD INTERFERE WITH THE FUNCTION OF THE SPEED CONTROL.

VEHICLE DESCRIPTION: SPORT UTILITY VEHICLES. THESE VEHICLES MAY HAVE A MIS-ASSEMBLED OR INCORRECTLY MANUFACTURED NUT THAT ATTACHES THE STEERING WHEEL ASSEMBLY TO THE STEERING COLUMN. THE NUT COULD BE UPSIDE DOWN IN THE STEERING WHEEL ASSEMBLY, WHICH COULD OVERSTRESS THE STEERING COLUMN SHAFT WHEN THE NUT IS TIGHTENED. IN ADDITION, SOME OF THE NUTS MAY HAVE BEEN CRACKED DURING MANUFACTURE RESULTING IN THE NUT FRACTURING WHEN IT IS TIGHTENED DURING VEHICLE ASSEMBLY.

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THESE VEHICLES HAVE JACKING INSTRUCTIONS WHICH, IF FOLLOWED, COULD CAUSE THE VEHICLE OPERATOR TO PLACE THE JACK ON A FRAME WELD WHEN ATTEMPTING TO RAISE A REAR WHEEL. IF THE VEHICLE IS JACKED UP WITH THE JACK PLACED ON THE FRAME WELD AND IF THE VEHICLE IS FREE TO ROLL (WHEELS NOT BLOCKED OR CHOCKED), THE JACK COULD YIELD AND THE VEHICLE MAY DROP SUDDENLY.

VEHICLE DESCRIPTION: 4-DOOR SPORT UTILITY VEHICLES EQUIPPED WITH SIDE AIR BAGS. THE SUBJECT VEHICLES HAVE A REVISED LEVEL SIDE CRASH SENSOR THAT COULD DEPLOY THE SIDE AIR BAG IF THE IGNITION KEY IS IN THE "RUN" POSITION AND THE SEATBELT WEBBING IS FORCIBLY EXTRACTED FROM A LOCKED RETRACTOR WITH A JERKING MOTION.

VEHICLE DESCRIPTION: MINI VANS. THESE VEHICLES MAY HAVE INCORRECTLY FUEL LINE END FORMS WHICH COULD RESULT IN A LOWER THAN SPECIFIED PULL APART FORCE FOR THE INSTALLED FUEL LINE CONNECTION.

VEHICLE DESCRIPTION: MINI VANS, LIGHT PICKUP TRUCKS, AND SPORT UTILITY VEHICLES. OFF LEASE CANADIAN VEHICLES EQUIPPED WITH DAYTIME RUNNING LIGHTS WHICH MEET CANADIAN REQUIREMENTS AND NOT THE PHOTOMETRIC REQUIREMENTS OF FMVSS 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." ACCORDING TO FORD, THE VEHICLES WERE IMPORTED INTO THE U.S. ERRONEOUSLY.

VEHICLE DESCRIPTION: F-SUPER DUTY STRIPPED MOTOR HOME CHASSIS BECAUSE THEY MAY HAVE A MISSING OR PARTIALLY INSTALLED BRAKE PEDAL TO MASTER CYLINDER PUSHROD RETAINING CLIP.

VEHICLE DESCRIPTION: PASSENGER VEHICLES USING AFTERMARKET FRONT PASSENGER SIDE SEAT BELT ASSEMBLIES THAT WERE SOLD BY FORD PARTS DEPARTMENTS FROM JANUARY 1, THROUGH JUNE 13, 2000. THESE SEAT BELT ASSEMBLIES FAIL TO COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 209, "SEAT BELT ASSEMBLIES." THE EQUIPMENT INVOLVED IS SERVICE STOCK SEAT BELT ASSEMBLIES, MODEL NOS. H 9977, H 9979, T 9063, AND T 9217, BUILT BY TRW VEHICLE SAFETY SYSTEMS, INC. (TRW) MANUFACTURED FROM JUNE 1, 1998 THROUGH MAY 21, 2000. SOME OF THESE SEAT BELT ASSEMBLIES MAY HAVE BEEN INSTALLED AS SERVICE REPLACEMENT EQUIPMENT ON THE VEHICLES INVOLVED IN THE RECALL.

VEHICLE DESCRIPTION: PASSENGER VEHICLES USING AFTERMARKET DRIVER'S SEAT BELT ASSEMBLIES THAT WERE SOLD BY FORD PARTS DEPARTMENTS FROM JANUARY 1, THROUGH JUNE 13, 2000. THESE SEAT BELT ASSEMBLIES FAIL TO COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 209, "SEAT BELT ASSEMBLIES." THE EQUIPMENT INVOLVED IS SERVICE STOCK SEAT BELT ASSEMBLIES, MODEL NOS. H 9977, H 9979, T 9063, AND T 9217, BUILT BY TRW VEHICLE SAFETY SYSTEMS, INC. (TRW) MANUFACTURED FROM JUNE 1, 1998 THROUGH MAY 21, 2000. SOME OF THESE SEAT BELT ASSEMBLIES MAY HAVE BEEN INSTALLED AS SERVICE REPLACEMENT EQUIPMENT ON THE VEHICLES INVOLVED IN THE RECALL.

VEHICLE DESCRIPTION: A WINDSHIELD WIPER CONTROL MODULE MAY NOT BE CAPABLE OF CARRYING THE CURRENT REQUIRED DURING HIGH LOAD CONDITIONS ON THE WIPERS (I.E., ICE, SNOW, OR OTHER DEBRIS).

VEHICLE DESCRIPTION: CUTAWAYS AND STRIPPED CHASSIS WITH SINGLE REAR WHEELS. THE LUG NUTS CAN POTENTIALLY BOTTOM OUT ON A SHOULDER ON THE STUDS.

VEHICLE DESCRIPTION: PICKUP TRUCKS EQUIPPED WITH 2.5L OHC ENGINES. ENGINE COOLANT CIRCULATION THROUGH THE HEATER CIRCUIT IS PREVENTED BECAUSE OF A PLUGGED HEATER RETURN TUBE (WATER PUMP INLET TUBE) AT THE WATER PUMP. THESE VEHICLES DO NOT COMPLY WITH THE INTENT OF FMVSS NO. 103, "WINDSHIELD DEFROSTING AND DEFOGGING SYSTEMS."

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THESE VEHICLES MAY HAVE BEEN BUILT WITH THE LEFT REAR SEAT BELT RETRACTOR ATTACHING BOLTS INCORRECTLY TIGHTENED.

VEHICLE DESCRIPTION: PASSENGER VEHICLES NOT EQUIPPED WITH THE ANTI-LOCK BRAKING SYSTEM (ABS). A PRESSURE CONSCIOUS REDUCING VALVE (PCRV) IN THE REAR BRAKES MAY BE SUBJECT TO CORROSION AND RESULT IN MALFUNCTION, WHEN OPERATED IN AREAS THAT USE SALT COMPOUNDS ON THE ROADWAY FOR DE-ICING OR DUST CONTROL.

AFTERMARKET TRAILER HITCH ASSEMBLIES. THE MOUNTING BOLTS AND NUT PLATES MAY BECOME LOOSE AND LOSE CLAMP LOAD, RESULTING IN A DISENGAGEMENT OF THE ATTACHING BOLTS FROM THE VEHICLE.

VEHICLE DESCRIPTION: MULTI-PURPOSE VEHICLES EQUIPPED WITH 4.0L ENGINES AND ALL-TIME 4-WHEEL DRIVE (A4WD) POWERTRAINS. THE GENERIC ELECTRONIC MODULE (GEM) COULD EXPERIENCE A CONDITION REFERRED TO AS "LOCK-UP" IN WHICH THE GEM CONTROLLED ELECTRONIC FUNCTIONS (E.G., FRONT WINDSHIELD WIPERS, INTERIOR LIGHTS, 4X4 SYSTEM, ETC.) COULD NOT BE TURNED ON OR, IN SOME CASES IF THE FUNCTION IS ON, COULD NOT BE TURNED OFF.

VEHICLE DESCRIPTION: MULTI-PURPOSE VEHICLES. THE TRAILER HITCH ASSEMBLY TO THE FRAME ATTACHING BOLTS COULD LOSE THE CLAMP LOAD.

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THESE VEHICLES MAY HAVE BEEN BUILT WITH LOWER THAN THE INTENDED LEVEL OF TORQUE ON THE BOLTS THAT ATTACH THE AIR BAG ELECTRONIC CRASH SENSOR MODULE TO THE VEHICLE.

VEHICLE DESCRIPTION: MINI VANS. THESE VEHICLES MAY HAVE BEEN BUILT WITH INCORRECT URETHANE, RESULTING IN AN ADHESIVE BOND RATHER THAN THE INTENDED MOLECULAR BOND FOR THE FRONT WINDSHIELD AND REAR LIFTGATE GLASS.